NuRich gray flip straw lid drying on a gray towel by a kitchen sink next to a clear straw and a thin straw cleaning brush

How to Clean a Straw Lid (and the Parts People Forget)

To clean a straw lid, take it off the bottle, pull out the straw, and wash every part in warm soapy water: the flip-up mouthpiece, the hinge and the channel it folds into, the socket under the lid where the straw attaches, the rubber plug, and the threads. Push a thin straw brush through the straw from both ends, rinse everything, and let the parts air-dry apart before you put the lid back together.

Why straw lids need more than a quick rinse

A straw lid has more small spaces than a flat cap. Water sits in the mouthpiece, in the hinge, in the channel where the mouthpiece folds down and in the spot where the straw meets the lid. A rinse under the tap reaches the outside, but not those corners. That is where residue and smells usually start, especially if you put anything other than water in your bottle.

The good news: a full wash takes about five minutes once you know where to look.

The parts people forget

Here is a checklist for a flip straw lid like the NuRich Wide Mouth Flip & Sip Straw Lid in gray ($14.99). Most people wash the top and the straw and stop there. These are the spots they skip:

  • Inside the flip-up mouthpiece. The opening you drink from is small and holds a drop of water every time you close it.
  • The hinge. The joint where the mouthpiece flips up and down traps water on both sides.
  • The channel the mouthpiece folds into. The recessed slot on top of the lid collects dust and drips.
  • The straw socket under the lid. Flip the lid over: the spot where the straw pushes on is easy to miss and stays wet the longest.
  • The rubber plug. The lid's listing says it has a rubber plug inside to help prevent leaks. Wash around it and in the groove it sits in.
  • The threads inside the lid. The ridges that screw onto the bottle hold on to drink residue.
  • The inside of the carry handle. It's the part your hand touches most.

NuRich gray wide mouth straw lid with extra straws and a straw brush

What you need

  • Warm water and a few drops of mild dish soap.
  • A thin straw brush (pipe-cleaner style) for the straw and the mouthpiece.
  • A small bottle brush or an old soft toothbrush for the hinge, channel and threads.
  • A clean towel or a dish rack for air-drying.
  • Optional: baking soda or white vinegar for a deep clean.

How to clean a straw lid, step by step

  1. Take it apart. Unscrew the lid from the bottle and pull the straw off the socket under the lid. If the rubber plug comes out easily, take it out gently with a fingertip. If it doesn't, leave it in place and don't pry it with a knife.
  2. Rinse. Run warm water through the straw and over the top and underside of the lid to loosen anything stuck.
  3. Clean the straw. Push the straw brush through from both ends with soapy water, then hold the straw under the tap and let water run through it.
  4. Clean the mouthpiece and hinge. Flip the mouthpiece up. Push the thin brush into the drinking opening, then scrub both sides of the hinge and the channel the mouthpiece folds into.
  5. Clean the underside. Scrub the straw socket, around the rubber plug and along the threads with the small brush.
  6. Wipe the outside. Wash the gray rubber-coated grip and the inside of the carry handle.
  7. Rinse well. Rinse every part until no soap bubbles are left, especially inside the straw and the mouthpiece.
  8. Air-dry apart. Leave the mouthpiece flipped up and the straw off. Put the parts on a rack or towel until they are completely dry, then push the straw back on and screw the lid onto the bottle.

Can you put a straw lid in the dishwasher?

The NuRich gray straw lid's listing says it can be washed on the top rack of a dishwasher. Take the straw off first, leave the mouthpiece open so water can get in and out, and place the lid on the top rack. A dishwasher won't reach inside a narrow straw, so still run the straw brush through it by hand. For how to load lids and what "top-rack safe" means, read Dishwasher-Safe Water Bottle Lids: What "Top-Rack Safe" Means and How to Wash Yours.

Deep clean: when it smells or looks spotty

  • Baking soda soak: mix about 1 tablespoon of baking soda in a bowl of warm water and soak the lid and straw for a few hours or overnight.
  • Vinegar soak: mix one part white vinegar with three parts warm water and soak the parts overnight.
  • Use one method at a time. Never mix vinegar or soap with bleach.

After a soak, wash and rinse as above. If the smell stays, see How to Get the Smell Out of a Straw Lid. If the straw draws slowly after cleaning, read Straw Lid Care: How to Fix a Clogged or Slow-Drawing Straw.

Putting it back together

Check that the rubber plug is seated flat in its groove before you screw the lid on. The listing is clear that the lid is not leak-proof: the rubber plug helps prevent leaks, but every bottle screws on a little differently. Tighten the lid fully, keep the mouthpiece closed when the bottle is in a bag, and carry it upright. The lid fits most wide mouth bottles with a 2.28 in neck, including Hydro Flask wide mouth.

A tip: keep a second lid for wash day

Straw lids take the longest to dry, because water hides in the straw, the hinge and the socket. A second lid means your bottle is ready while the straw lid dries overnight. The NuRich Loop Lid ($9.99) is a wide mouth chug lid with a carry loop and a leak-proof rubber gasket. It fits 2.28 in neck, 12-64 oz bottles and is top-rack dishwasher safe.

How often to clean a straw lid

  • Every day (water only): rinse the lid, run water through the straw and leave it open to dry overnight.
  • Once a week: the full take-apart wash above.
  • Right away: after anything other than water, like sports drinks, juice or coffee.

Need a new one? See the NuRich Wide Mouth Flip & Sip Straw Lid (gray): BPA-free, rubber-coated, fits 2.28 in wide mouth necks and top-rack dishwasher safe.

FAQ

How do you clean the inside of a straw lid?

Take the straw off, then push a thin straw brush through the flip-up mouthpiece and scrub the hinge, the straw socket under the lid, the rubber plug and the threads with warm soapy water. Rinse well and air-dry with the mouthpiece open.

How do you clean a water bottle straw without a brush?

Soak the straw in warm soapy water, then run hot tap water through it with force. A brush cleans better, so it's worth keeping a thin straw brush for weekly washes.

Can straw lids go in the dishwasher?

Check your lid's listing. The NuRich gray straw lid can go on the top rack. Take the straw off and still brush the inside of the straw by hand.

How often should I clean my straw lid?

Rinse it every day and do a full take-apart wash at least once a week. Wash it right away after anything other than water.

Why does my straw lid still smell after washing?

Water is usually trapped in the hinge, the straw socket or around the rubber plug. Soak the parts in baking soda or vinegar water, wash again and let every part dry completely apart.


Written by the NuRich team in Winder, GA. We cite primary sources and only state what's on our product listings.
The NuRich team · Clean water for everyone.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.